Smc-networks Pursuit Series PRO-9675FT4 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Smc-networks Pursuit Series PRO-9675FT4. SMC Networks Pursuit Series PRO-9675FT4 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 24
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
4 Channel Remote Car Starter
With Full Feature Alarm System
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents:
Remote Start/Alarm Control Module
(2) - Four Button Anti Code Grabbing Transmitters
4 Channel Code Learning Receiver
External Superheterodyne Antenna/Receiver
Mini Six Tone Siren
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Output Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
(1) - Two Pin Control Switch
(1) - Four Pin Shock Sensor Harness
(1) - Two Pin Door Lock Harness
(1) - Dual Stage Shock Sensor
(1) - Starter Inhibit Relay and Socket
(2) - 30 Amp In-line Fuse Holders With Fuses
(1) - Pin Switch Hardware Bag
(2) - Under Hood Caution Labels
(1) - Installation Manual
(1) - Operator's Manual
(1) - Limited Warranty
(2) - Window Decals
Model PRO-9675FT4
Installation Manual
Zobrazit stránku 0
1 2 3 4 5 6 ... 23 24

Shrnutí obsahu

Strany 1 - Model PRO-9675FT4

4 Channel Remote Car StarterWith Full Feature Alarm SystemInstallation InstructionsThis Unit Is Intended For Installation In Vehicles With12 Volt Nega

Strany 2

Orange Wire: Ground When Armed OutputThis wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibitrelay.

Strany 3

Black Wire: Chassis Ground SourceConnect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Becertain to

Strany 4

Dark Blue Wire: Delayed 300mA Pulsed Channel 3 OutputThe Dark Blue wire supplies a 300mA ground pulsed output whenever channel three of the receiver

Strany 5

13started under control of the remote start unit. Typically this wire will be used to re-lock the vehicle doors ifthe doors unlock automatically when

Strany 6 - Siren Wiring Detail

factory door lock switch to the factory door lock relay.The Green wire of the door lock harness provides a ground pulse during the disarming sequence,

Strany 7 - Hood Pin Switch Detail

cut wire to terminal 87a of the optional relay added. Connect the green wire of the 3 pin harness to terminal 86of the optional relay added. Connect

Strany 8

Note: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 VoltDoor Lock Control CircuitsThese applications require the

Strany 9 - Entry Illumination Detail

17To program these selectable features;Action System ResponseTurn ignition on No responsePress and release the valet switch 3 times 1 Chirp - LED 1 f

Strany 10 - Starter Inhibit Wiring Detail

a 4 hour timed start interval. The lights will flash and the siren will chirp 2X or 4X dependant upon 2 or 4 hourinterval setting.NOTE: Once selected,

Strany 11

The Remote Start Unit will learn the tach rate of most vehicle's single coil, multiple coil packs, or singleinjector. To learn tach.1. Turn the

Strany 12 - Channel 3 Relay Wiring Detail

The PRO-9675FT4 Remote Start/Alarm System is designed to be used with Automatic TransmissionVehicles Only! The unit provides a selectable ignition co

Strany 13

20TESTING YOUR INSTALLATION:CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote StartDevice. It is the

Strany 14

217. Keeping the brake pedal depressed, activate the RF transmitter in an attempt to start the vehicle. The car should not start.8. Repeat the abov

Strany 15

KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are twoalternatives availabl

Strany 16

23METHOD 2To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the ke

Strany 17

© 2000 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-5870AWIRING DIAGRAM

Strany 18

drill a 1/4" hole in the desired location and pass the connector end of the LED through the hole and towardthe control module. Press the LED fir

Strany 19

The PRO-9675FT4 is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although thiscombination Alarm/Remote Start unit is a sophisticated syst

Strany 20

BLUE Wire: Ignition 1 OutputConnect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when theignition key is

Strany 21

WIRING CONNECTIONS: Multi Pin Accessory Input/Output HarnessWhite w/ Red Trace Wire: Parking Light Flasher FeedThis wire is the common contact of the

Strany 22 - METHOD 1

Purple Wire: (+) Door Trigger InputIf the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and someImports)

Strany 23 - COMPLETING THE INSTALLATION:

General Motors VATS By-Pass DiagramLight Blue Wire: Ignition 3 OutputThis wire provides a 300mA ground output that becomes active 3 seconds before t

Strany 24 - WIRING DIAGRAM

Green w/ White trace Wire: Entry Illumination Ground OutputThis wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to

Komentáře k této Příručce

Žádné komentáře